How to clean a mechanical keyboard, step by step
To clean a mechanical keyboard, unplug it, remove the keycaps, get rid of loose dirt on the plate with a vacuum or brush, and wash only the keycaps in warm soapy water. The rest of the board stays dry. Refit the keycaps once they have dried completely, which usually means leaving them overnight.
Three levels of cleaning
Most of the time you don't need to take anything apart. Pick the level that matches what you can see:
| Level | When | What you do | Water involved |
|---|---|---|---|
| Surface | Dust, crumbs, fingerprints | Tip the board over, brush, wipe with a barely damp microfibre cloth | Almost none |
| Full clean | Grime between keys, greasy keycaps. Xataka suggests every few months, depending on use and whether you eat at your desk | Remove keycaps, vacuum the plate, swab the corners, wash the caps | Keycaps only |
| Spill | Any liquid gets inside | Disconnect immediately and follow the spill section below | None added until it has been assessed |
What you need
- Keycap puller: many keyboards include one, and Xataka puts the cost of buying one at under 10 euros.
- Vacuum with a narrow nozzle and a stiff brush. A dry toothbrush works.
- Microfibre cloths. Avoid kitchen paper: it sheds fibres and can scratch.
- Cotton swabs and isopropyl alcohol. TechRadar lists a 70% solution.
- A bowl and mild dish soap for the keycaps, plus a towel to dry them on.
Quick clean, keycaps on
- Disconnect the board. Unplug the cable and switch off wireless mode. Corsair asks you to wait at least 5 seconds after unplugging before you start.
- Turn it upside down and shake lightly. Don't bang it against the desk.
- Brush or vacuum between the rows. A vacuum picks up what a brush only moves around.
- Wipe the keycaps and case with a slightly damp cloth, then a dry one. Nothing should drip.
Full clean, keycaps off
- Photograph the layout. It takes seconds and saves you from guessing later, especially on smaller layouts where the legends carry secondary functions.
- Pull the keycaps straight up. Das Keyboard warns that pulling at an angle can damage the switch. Go gently on the long keys with stabilizers (spacebar, Enter, Shift, Backspace): TechRadar recommends easing the spacebar up slowly.
- Clean the plate. Vacuum first, using tweezers for any hair or stuck debris. Then run an alcohol-dampened swab along the gaps. Alcohol suits this job because it evaporates quickly, but the swab should be damp, not soaked, and it should stay off the inside of the switches.
- Soak the keycaps. Submerge them in warm soapy water. Corsair says 30 to 60 minutes, which is enough for normal dirt.
- Rinse and dry. Rinse each one with clean water, towel them and leave them overnight. TechRadar's method is to drain them face up for a few hours, then turn them face down. The underside matters most, because that is the part that sits on the switch. The cross-shaped parts of stabilizer keys are slowest to dry, so wipe those too.
- Refit them using your photo. Start with the stabilizer keys, then press the rest straight down.
- Test every key in a text editor before you call it done.
Where the guides disagree
Reading several sources side by side shows that some popular advice conflicts. Here is what each one says and what we would do:
| Question | What sources say | Our recommendation |
|---|---|---|
| Compressed air | Corsair and Das Keyboard use it. Xataka generally advises against it because of condensation and because it moves dirt around. | Vacuum first. If you use air, short bursts from a distance and from the side. Remove any loose stabilizer parts first. |
| Water temperature | Corsair and Xataka say warm. TechRadar says hot. Akko warns that heat can deform plastic. | Warm. It does the job and rules out the risk. |
| Soak time | Corsair 30-60 minutes, TechRadar a few hours, Xataka 5-6 hours with denture tablets. | Start with an hour. Only go longer if grime remains. |
| Drying faster | Akko allows a hair dryer on cold only, never hot. | Air-dry overnight. There is rarely a reason to hurry. |
None of the guides we checked recommends a machine dishwasher. Given the heat warnings, we would skip it, and we would keep acetone away from keycaps as well: the Deskthority wiki notes that ABS doesn't cope with solvents. Our PBT vs ABS guide explains the differences between the two materials.
If you spill something on it
Speed matters more than technique. Disconnect it right away, and don't test it to see if it still works. What comes next depends on the liquid:
- Water: turn the board face down so it drains, remove the keycaps and blot with a cloth. Let it air-dry for several hours and only reconnect it when it is completely dry.
- Coffee, soft drinks or anything sugary: do the same, then do a full clean straight away. Sugar left behind dries sticky and can make keys bind.
On a soldered board, a switch ruined by a spill means desoldering. On a hot-swap board you pull the switch and fit another, as our hot-swap guide shows. If liquid has reached deep inside, don't open the board unless you are comfortable doing so.
Common mistakes
- Refitting keycaps while still damp. Corsair is explicit: wait until they are dry, because liquid on the circuit board can cause problems.
- Submerging the keyboard itself. Akko is firm on this: never. Only the keycaps go in water.
- Spraying cleaner directly on the board. Apply it to the cloth or swab instead.
- Scrubbing with abrasives. They polish the surface and speed up shine on the keycaps.
Cleaning a TESSEN keyboard
The TESSEN keyboard is a 60% ANSI board with 61 keys, so a full clean means fewer keycaps to remove and wash than on a larger board. Its PBT doubleshot keycaps have legends made of plastic rather than ink, so soap and water have no printed layer to wear away. The ABS case gets the damp cloth treatment, not a soak.
Two details are worth keeping in mind. It has internal foam, one more reason not to let liquid get inside. And the plate is hot-swap for MX switches with 3 and 5 pins, so if a switch does suffer, you can replace it without soldering. The Gateron KS-3 Milky Pro Yellow switches and Gateron stabilizers come lubricated, and that is not something a routine clean should touch: keep alcohol and water away from them.
If you are after a new look once it is clean, the 3D configurator lets you choose the colour of every key. Warranty and returns are covered in the FAQ.
Sources
- Corsair: tips on cleaning your keycaps and keyboard
- Xataka: how to deep-clean a mechanical keyboard (Spanish)
- TechRadar: how to deep-clean a mechanical keyboard (Spanish)
- Akko: how to clean your mechanical keyboard (Spanish)
- Das Keyboard: how to change the keycaps on a keyboard
- Deskthority wiki: keycap materials
Keep reading