PBT vs ABS keycaps: why they don't shine or wear off
PBT keycaps don't turn shiny with use because PBT is a harder, denser plastic than ABS, which is the material that wears smooth and ends up looking polished on the keys you hit most. Whether the letters wear off is a separate question: it depends on how the legend is made. On a doubleshot keycap the legend is a second piece of plastic that runs through the key, so there is no ink to lose.
What ABS and PBT are
They are the two most common keycap plastics. ABS (acrylonitrile butadiene styrene) is what most office keyboards and many gaming boards use: cheap to produce, easy to mould and smooth with a slight gloss out of the box, according to the Deskthority wiki. PBT (polybutylene terephthalate) is a harder polyester that handles heat and chemicals better, but it is trickier to mould, which is why it has historically been less common.
The material data explains a lot of what you feel under your fingers:
| Property | ABS | PBT |
|---|---|---|
| Structure | Amorphous | Semi-crystalline |
| Density | 1.03-1.07 g/cm³ | 1.30-1.32 g/cm³ |
| Softening or melting point | Softens around 100-105 °C (glass transition) | Melts at 220-230 °C |
| Typical finish | Smooth, slightly glossy | Matte, textured |
| After years of use | Shines on the most used keys; can yellow under UV | Keeps its texture; does not yellow under UV |
| Shrinkage when moulded | Low | High, which makes long keys like the spacebar harder to produce |
Density and temperatures: NETZSCH lab data for each polymer. Behaviour in use: Deskthority wiki.
Density is the easiest number to translate into feel: PBT weighs about 25% more for the same volume. That is why a PBT keycap tends to feel more solid, and why the home test Deskthority suggests for telling them apart is dropping them in water: ABS tends to float higher and PBT sinks faster.
Why ABS keys go shiny
Many people assume the shine is built-up grease. It isn't, or not only. Shine appears when finger friction smooths out the surface micro-texture and exposes polished plastic that reflects light. Skin oils help wear soft surfaces like ABS faster, but cleaning won't fix it: a shiny key is polished, not dirty, as Gear Patrol explains.
That is why shine always shows up on the same keys: spacebar, WASD, E, A or left Ctrl, depending on how you use the board. KeebsForAll notes that ABS keycaps often show wear within months.
PBT wears too, but because it is harder it does so far more slowly, and its matte starting texture hides the change for years. It isn't indestructible; it just takes much longer to change how it looks.
Why legends don't wear off: it's the legend method
This is the most common mix-up. Material and legend are two separate choices: you can have PBT with printed letters that rub off and ABS with letters that last forever. The usual methods:
| Method | How it's made | Legend lifespan | Lets RGB through |
|---|---|---|---|
| Doubleshot | Two plastics are injected into the mould: one forms the key, the other the legend, which goes all the way through | Won't wear off: the legend is plastic, not ink | Yes, if the legend plastic is translucent |
| Dye-sublimation | Heat turns the dye into a gas that penetrates the plastic | Very durable; used mainly on PBT | No |
| Laser marking | A laser marks or darkens the surface | Varies with the finish | Depends on the design |
| Pad printing | Ink applied on the surface | Wears away on the most pressed keys | Depends on the design |
Two things worth knowing when you buy. Dye-sub works because PBT survives the heat of the process, but vivid legends on dark keys are hard to achieve, as Cerakey points out. And doubleshot has traditionally been an ABS technique, because PBT shrinks more as it cools and the two parts are harder to fit precisely. That is why many high-end enthusiast sets, such as GMK, are still doubleshot ABS: the legends never wear off, even if the surface eventually shines.
So which should you pick?
- If you want the keyboard to look the same in three years: PBT, ideally with doubleshot or dye-sub legends.
- If you use backlighting and want light through the legends: doubleshot with a translucent legend. Dye-sub doesn't let light through.
- If you like a smooth feel and very saturated colours: doubleshot ABS is a valid choice, knowing it will shine.
- If budget comes first: above all, avoid printed legends on keys you use every day. A legend that disappears is more annoying than a bit of shine.
On sound, guides like KeebsForAll's describe PBT as deeper and crisper and ABS as higher-pitched, but wall thickness, keycap profile and the keyboard itself matter so much that sound alone shouldn't decide it.
How to care for your keycaps
- Take a photo of the keyboard before removing anything, so you can put every key back.
- Remove them with a keycap puller, pulling straight up.
- Wash them in warm water with a little soap and rub gently. Scouring pads or abrasive materials speed up the polishing that causes shine.
- No acetone or solvents on ABS: they attack it. Deskthority uses acetone as a test precisely because it smears ABS.
- Let them dry completely before refitting, so no moisture reaches the switches.
- Keep light ABS out of direct sun: UV encourages yellowing.
If your keyboard is hot-swap, use the clean-up to check the switches too. Our hot-swap keyboard guide walks through it step by step.
The keycaps on the TESSEN keyboard
The TESSEN keyboard uses PBT doubleshot keycaps with MX stems: the material that doesn't shine combined with the legend that doesn't wear off. You can pick the colour of every key from eight options (Black, White, Grey, Matcha, Blue, Sky, Pink and Red) in the 3D configurator, rotate the model to check the result and save the design with its Design ID. It's a 60% ANSI board with 61 keys; if you're unsure about the format, the 60% keyboard guide explains it. Prices start at €119.99, VAT included.
Because the stems are standard MX, you can also fit other MX-compatible keycaps. Questions about shipping, returns and warranty are answered in the FAQ.
Sources
Keep reading