Keycap profiles: Cherry, OEM, SA, DSA and XDA
A keycap's profile is its shape seen from the side: how tall it is, how its top is angled and whether that changes from row to row. The five you will run into most are Cherry, OEM, SA, DSA and XDA. The first three are sculpted (each row has its own shape) and the last two are uniform (every key is the same), and that difference decides which keys you can move around and how typing feels.
Sculpted or uniform: the difference that matters
On a sculpted profile, every row has a different height and angle, so the tops of all the keys form a gentle curve under your fingers. The Deskthority wiki explains that the goal is to even out finger travel between rows, and that most desktop keyboards have used sculpted keys since the mid-1980s.
On a uniform profile, every key has the same shape and height. The overall surface is flat and any key works in any position.
Deskthority sums up the practical consequence: on a keyboard with sculpted keycaps you can't swap keys between rows without making the profile uneven. If your keycaps will always stay in their usual spots, it doesn't matter. If you want to rearrange, it does.
The five profiles compared
None of the sources we checked measures every profile the same way, and the millimetre figures that circulate online don't agree from one site to the next. So the table compares relative heights rather than quoting numbers that can't be checked.
| Profile | Rows | Height | Top surface | Suits you if... |
|---|---|---|---|---|
| Cherry | Sculpted | Low-medium; slightly lower than OEM | Cylindrical | You want a familiar, low feel for typing and gaming |
| OEM | Sculpted | Medium | Cylindrical | You're coming from a stock keyboard and don't want to notice the change |
| SA | Sculpted | Tall; the tallest of the five | Spherical, deeply concave | You like the retro look and don't mind more finger travel |
| DSA | Uniform | Low | Spherical, slightly concave | You use alternative layouts or want to move keys around |
| XDA | Uniform | Low-medium | Wide and nearly flat | You want large key tops and freedom to rearrange |
Classification based on Deskthority, KeebsForAll, Wooting and Akko. One figure is well documented: Deskthority puts DSA at 0.291 inches (7.39 mm), the same height as OEM's home row.
Cylindrical or spherical
This is the other trait you can feel with your eyes closed. A cylindrical top curves in one direction only, like a slice of tube: it guides your finger side to side, but not top to bottom. A spherical top is concave in every direction, like a spoon, and steers your finger to the centre of the key. Cherry and OEM are cylindrical; SA and DSA are spherical. The deeper the dish, the stronger that guidance.
How rows are numbered
If you buy single keys or an accent kit, you'll see labels like "R1" or "row 4". Not every brand counts the same way. This is how Deskthority maps the rows of a QWERTY keyboard, top to bottom:
| Keyboard row | Signature Plastics numbering (SA, DSA) | Cherry numbering |
|---|---|---|
| Function keys (F1-F12) | 1 | E |
| Numbers | 1 | E |
| Tab, Q, W, E... | 2 | D |
| Caps Lock, A, S, D... | 3 | C |
| Shift, Z, X, C... | 4 | B |
| Spacebar and modifiers | 3 or 4 | B |
On a 60% board this has a useful reading. With no function row, Esc sits in the number row, which in both numbering systems shares its profile with the function row. So a regular accent Esc fits in place without looking tilted.
What changes on a 60% keyboard
On a compact board, keys get moved around more often than you'd think. The classic case is using Caps Lock as Ctrl or Fn, which our 60% keyboard guide recommends so you can reach the arrows without moving your hands. If you only change the function in software, the keycap stays put and nothing changes. But if you also move the physical Ctrl keycap (bottom row) to the Caps Lock position (row 3), on a sculpted profile it will sit at a different angle from its neighbours.
You have three options:
- Keep the original keycap and change only the function. This is the simplest route.
- Get the key in the right row. If you buy a single Ctrl for that spot, check the listing says it's row 3.
- Switch to a uniform profile such as DSA or XDA if you rearrange a lot, for example for layouts like Colemak or Dvorak, which KeebsForAll lists as a typical use for DSA.
How to choose, step by step
- Start from what you know. If you're comfortable with your current keyboard, Cherry or OEM is the smallest change. Deskthority describes Cherry as somewhat lower than the standard profile, and the difference is subtle.
- Decide whether you'll move keys. If yes, go uniform (DSA or XDA). If not, any profile works.
- Think about height. A tall profile like SA puts your fingers further from the desk. KeebsForAll notes that tall profiles often call for a wrist rest and low ones reduce wrist extension. If you type for hours, start with a low or medium profile.
- Try before buying a full set. A few loose keys in the positions you use most will tell you more than any table.
- Don't choose on sound alone. Guides link SA with a deeper sound and Cherry with a more muted one, but material, wall thickness and the keyboard itself matter as much or more. We cover that in our PBT vs ABS keycaps guide.
Before you buy keycaps: a checklist
- Stem: it must match the switch. For MX-style switches, an MX cross stem. KeebsForAll points out that profile rarely causes problems on its own: the issues come from stem type and layout.
- Layout: ANSI or ISO. The Enter key and left Shift are different sizes in each.
- Bottom-row sizes: spacebars and modifiers vary between keyboards. Compare your board's sizes in units (u) with what the kit includes.
- One profile per row: Deskthority warns that mixing keys from nearly compatible profiles in the same row can look uneven. If you combine kits, keep them to the same profile.
The keycaps on the TESSEN keyboard
The TESSEN keyboard is a 60% ANSI board with 61 keys, PBT doubleshot keycaps and MX stems. In the 3D configurator you choose the colour of each key from eight options (Black, White, Grey, Matcha, Blue, Sky, Pink and Red), rotate the model and save the design with its Design ID. Prices start at €119.99, VAT included.
Because the stems are standard MX, you can try other MX-compatible keycaps if you want a different profile, as long as the kit covers the ANSI layout. You can also browse our keycaps. If you're unsure whether a particular set will fit, email us at tessenshop@gmail.com before buying, and for shipping and returns see the FAQ.
Sources
- Deskthority wiki: keyboard profiles and row numbering
- Deskthority wiki: Signature Plastics SA family
- Deskthority wiki: Signature Plastics DSA family
- KeebsForAll: Cherry, SA, OEM and DSA profiles explained
- KeebsForAll: keycap profiles and materials buying guide
- Wooting: keycap profiles explained
- Akko: everything about keycaps (Spanish)
Keep reading