Hot-swap keyboard: how to change switches without solder

By | Published

A hot-swap keyboard has metal sockets on its PCB that hold each switch by friction, so you can pull one out and put another in without a soldering iron. All you need is a keycap puller, a switch puller and a bit of patience the first few times. The two things to watch are whether the switch is compatible with the socket and whether its metal pins are straight when it goes in.

What hot-swap actually means

On a traditional mechanical keyboard, the two metal pins of each switch are soldered to the PCB. Replacing a switch means desoldering, cleaning the hole and soldering again. On a hot-swap board, every position has a socket with two spring contacts that grip the pins: the socket makes the electrical connection and, together with the mounting plate, keeps the switch in place.

The Deskthority wiki defines the term as replacing components without soldering or desoldering. There are several socket types, which is why not every board accepts everything:

Socket type How it is mounted What to know
Kailh (and similar ones from Gateron or Glorious) Surface-mounted on the underside of the PCB The most common type on factory hot-swap boards. Only works on PCBs designed for it. Comes in an MX or a Choc (low profile) version, never both.
Mill-Max Pressed into the solder holes Can convert some boards designed for soldering. The 0305 model raises the switch 0.64 mm above the PCB.
Outemu Brand-specific According to Keebio, it only takes Outemu switches and a few others with the same pin dimensions.

In practice: if the manufacturer says the board is MX hot-swap, almost any MX-style switch will fit. If it doesn't say so, don't try to pull the switches out; they are probably soldered.

Before buying switches: compatibility

3-pin or 5-pin

Every MX switch has two metal pins (the ones that conduct) and a central plastic post. 5-pin switches add two thinner plastic legs on the sides, which only make the switch sit more firmly on the PCB. That decides what fits:

Switch 5-pin board 3-pin board
3-pin Fits as is. It may come out with the keycap when you pull it. Fits as is.
5-pin Fits and sits more firmly. Clip the two plastic legs, never the metal pins.

Glorious stresses that only the two plastic legs get clipped, and KeebsForAll warns that doing so may affect the switch warranty. If your board takes both types, you can skip this step entirely.

What won't go into an MX socket

Low-profile Choc-style switches use a different socket, as splitkb notes on its Kailh socket listing. Optical and other contactless switches rely on a different sensing system on the PCB, so they won't work on a board built for MX contact switches either. Always check the keyboard's spec sheet before you buy.

Tools

  • Keycap puller: to lift keycaps off without stressing their sides.
  • Switch puller: a two-pronged tool that presses the switch's clips. KeebsForAll recommends IC-chip-style pullers and advises against small ones or those combined with a keycap puller.
  • Fine tweezers: to straighten a bent pin.
  • Optional: compressed air to clean the socket and a soft surface to work on.

How to swap switches, step by step

  1. Disconnect the keyboard. Unplug the cable and, if it's wireless, turn it off.
  2. Take a photo of the board. It helps you put keycaps back and shows the orientation of the original switches.
  3. Remove the keycaps from the keys you're changing. Pull straight up without rocking.
  4. Check the switch orientation. Before removing it, note which side the metal pins are on. The new one has to go in the same way; rotated, it won't line up with the contacts.
  5. Pull the switch. Slide the puller's tips into the gaps in the plate where the two clips sit (above and below the switch), squeeze and pull straight up. If it resists, lift one side slightly, then the other. Don't squeeze too hard: the housing can crack.
  6. Inspect the new switch's pins. They should be straight and parallel. If one is bent, straighten it gently with tweezers.
  7. Line it up and press gently. Align the pins with the holes and press evenly on both sides until you feel or hear the clips snap in. It should take very little force; if you have to push hard, take it out and check the pins again.
  8. Test before refitting keycaps. Plug the keyboard in and press every swapped key in a text editor or an online keyboard tester.
  9. Put the keycaps back using your photo.

If you're replacing a lot of switches, KeebsForAll suggests starting with the corners and then working row by row, so the plate stays evenly supported.

If a key stops working

Symptom Likely cause Fix
Key doesn't type A bent metal pin that missed the contact Remove the switch, straighten the pin and reinsert it
Switch wobbles or sits higher Not fully clipped into the plate Press straight down until the clips snap
Switch comes out with the keycap 3-pin switch with little grip, or a tight keycap Hold the switch down with a finger while pulling the keycap
A switch that worked now fails Dust in the socket or a damaged socket Clean with compressed air and try another switch in that spot

Glorious points out that a pin you've already straightened is weaker and bends more easily. If it happens twice with the same switch, set that switch aside.

How many times can you swap

Sockets don't last forever. Kailh rates its sockets for about 100 insertion cycles, according to the listings from retailers such as splitkb and Keyboardio. One cycle is inserting and removing a switch in the same position, so the limit applies to each socket individually, not to the whole keyboard. If you change switches once or twice a year, or try a few on WASD, that's plenty of headroom.

What does shorten their life is careless handling: inserting switches at an angle or pushing down hard, which Deskthority says can even tear the socket's solder pads off the PCB. And if you want to try many different switches before deciding, a switch tester saves wear on the keyboard.

What hot-swap gets you

  • Try before you commit: swap a few keys to tactile or clicky switches and compare for a few days. Our guide to linear, tactile and clicky switches covers the differences with data.
  • Fix a key: if a switch fails, you replace it in two minutes instead of sending the keyboard in for repair.
  • Mix and match: heavier switches on the spacebar or on keys you hit by accident, lighter ones on the letters.
  • Maintenance: you can take a switch out to clean or lube it without any soldering gear.

Hot-swap on the TESSEN keyboard

The TESSEN keyboard is a 61-key 60% ANSI board with a hot-swap PCB that takes 3-pin and 5-pin MX switches. It does not accept low-profile or optical switches. It ships with lubed Gateron KS-3 Milky Pro Yellow linear switches, lubed Gateron stabilizers and internal foam, so most people won't need to change anything; hot-swap is there for when you want to try a different feel. If you're unsure about the size, the 60% keyboard guide explains how it works.

The keycaps are PBT doubleshot with an MX stem, and you can pick the colour of each one in the 3D configurator, from €119.99 including VAT. Warranty and returns are covered in the FAQ.

Sources

Keep reading

All guidesAll news