Keycap sizes: what 1u, 2u and 6.25u mean
Keycap sizes are measured in units (u): 1u is the width of a normal letter key, and every other key is a multiple of it. A 2u key takes the space of two letters, and a 6.25u spacebar the space of six and a quarter. Knowing these numbers is how you find out, before paying, whether a keycap set will fit your keyboard.
What a unit actually is
The Deskthority wiki defines the unit as a measure of key width based on a normal letter key, which is 1 unit tall and 1 unit wide. According to Cherry, quoted on the same wiki, 1u is 19.05 mm, exactly 0.75 inches.
Worth knowing: there is no international standard that fixes that value today. The old ISO 1091 specified 19 mm with a 1 mm tolerance, but it was withdrawn in 1994. In practice, almost every full-size and compact keyboard uses about 19 mm, which is why keycaps from different brands swap so easily in most cases.
One more detail: the unit describes the slot a key takes in the grid, not the plastic itself. The physical cap is slightly narrower so it clears its neighbours. Deskthority, for example, lists a 6.25u spacebar as 118 mm wide, against the 119 mm you would get by multiplying.
From units to millimetres
Use this table to check the size of a key on your board with a ruler. The millimetre figures are the slot each size occupies, worked out at 19.05 mm per unit.
| Size | Approximate slot | Where you'll find it |
|---|---|---|
| 1u | 19.1 mm | Letters, numbers, Esc |
| 1.25u | 23.8 mm | Ctrl, Alt, Win and Fn on the bottom row |
| 1.5u | 28.6 mm | Tab |
| 1.75u | 33.3 mm | Caps Lock |
| 2u | 38.1 mm | Backspace |
| 2.25u | 42.9 mm | Enter and left Shift |
| 2.75u | 52.4 mm | Right Shift |
| 6.25u | 119.1 mm | Most common spacebar |
| 7u | 133.4 mm | Longer, less common spacebar |
If your measurement lands between two rows, go with the closer one. Because of the gap between caps, you will never read the exact figure.
A 60% ANSI board, key by key
Das Keyboard describes the typical 60% ANSI board as 61 keys on five rows: 14, 14, 13, 12 and 8. Most are 1u; the exceptions sit at the ends of each row and along the bottom. These are their sizes according to Omnitype's ANSI layout guide, which also flags which ones use a stabilizer:
| Key | Size | Keyboard row | Stabilizer |
|---|---|---|---|
| Esc | 1u | Numbers | No |
| Backspace | 2u | Numbers | Yes |
| Tab | 1.5u | Q, W, E... | No |
| Caps Lock | 1.75u | A, S, D... | No |
| Enter | 2.25u | A, S, D... | Yes |
| Left Shift | 2.25u | Z, X, C... | Yes |
| Right Shift | 2.75u | Z, X, C... | Yes |
| Ctrl, Win, Alt, Fn | 1.25u | Bottom | No |
| Spacebar | 6.25u | Bottom | Yes |
The practical takeaway: on a 60% ANSI board only five keys are stabilized, and nearly every fit problem comes from them and from the bottom row.
Why the spacebar is the tricky key
Keys of 2u and up have a stabilizer on top of the central stem: a wire with two side mounts that stops the key tilting when you press it near one end. Those side mounts sit at a fixed distance from the centre, and the keycap needs its connectors exactly there.
On the spacebar the difference is large. Deskthority lists several layouts for 6.25u; one of the most common puts the stabilizer mounts 50 mm either side of the centre. On a 7u bar they sit at 57.15 mm, that is, three units. So a 7u bar isn't just longer than a 6.25u slot: its connectors don't line up with the stabilizer.
That's why, when a keycap set promises "spacebars for multiple layouts", what matters is that it includes a 6.25u bar if your board uses one.
The most common fit problems
- A different bottom row. Kinetic Labs points out that the spacebar, Shifts, Enter, Backspace and bottom modifiers are where trouble usually starts, and that some boards need smaller or extra keys compared with the standard layout.
- Boards with proprietary keys. The same guide warns that some peripheral brands use non-standard bottom rows or keys, so third-party sets may not fit.
- Special layouts. Formats such as Alice use shorter spacebars that sets don't always include.
- The wrong row on sculpted profiles. A 1.25u bottom-row Ctrl can sit at the wrong angle in another row. Our keycap profiles guide explains why.
- Switch orientation. Kinetic Labs notes that on boards with north-facing switches some Cherry-profile caps can touch between rows; south-facing boards have wider compatibility.
How to check that a keycap set fits
- Identify the layout. This guide covers ANSI, with the single-row rectangular Enter. On an ISO board, Enter and left Shift are different.
- Measure the keys that aren't 1u with a ruler and compare them with the millimetre table. Start with the spacebar and right Shift.
- Count the bottom-row keys and measure one. A typical 60% ANSI board has eight, with 1.25u modifiers.
- Read the set's kit list, not just the photo. Look specifically for "6.25u", or your spacebar size, and "2.75u" for right Shift.
- Confirm the stem. For MX-style switches, an MX cross stem.
- If in doubt, ask before buying from the shop selling the set, with the measurements you took.
Keycaps on the TESSEN keyboard
The TESSEN keyboard is a 61-key 60% ANSI board with PBT doubleshot keycaps on MX stems. In the 3D configurator you pick the colour of each key from eight options (Black, White, Grey, Matcha, Blue, Sky, Pink and Red), rotate the model and save your design with its Design ID. It starts at €119.99 including VAT.
Because the stems are MX, you can try other compatible keycaps as long as the set covers a 60% ANSI layout; if you're unsure about the format, the 60% keyboard guide explains it. You can also browse our keycaps. If you're not sure a particular set will fit, email us at tessenshop@gmail.com before you buy, and check the FAQ for shipping, returns and warranty.
Sources
Keep reading